Standard Industrial | Hydraulic Press Brakes, Shears, Presses

Backgauges

1, 2 or 3 Axis (X, Y, and R) CNC controls - U.S. Made Automec CNC controls - Waltham, MA


Automec CNC300	Automec CNC4000 (see below for additional information)	Automec G24HD 3 axis backgauge

300 job programmability	10,000 job storage/32 bends per job
Automatic calibration to tool heights	Floppy disk drive w/extra 1,000 jobs per disk
RS232 download port	Full color 9.5" graphics screen
16 digit alpha-numeric part numbers	Angle or ram depth programming with direct conversion
Angle adjust for angle correction	Pop Up "Windows" w/8 bends on one screen
11 digit job number
Both Automec Gauges Are Equipped With The Following
Single entry Ram offset & Bend allowance		Tooling Library
Inch/Millimeter conversion		Parts Counter
Backgauge reversal on pinch point		Help screens
1, 2 and 3 axis capability		Teach Mode
Up to 48" travel (24" is standard)		Off-line programming
Incredibly Quick and Simple job set-up		2 Year Parts Warranty

EVC 7 2D Graphical Controls

Axis Capability

Single X: In and out ot the backstop
Single Y: Depth/Angle of the ram
Single R: Height of the backstop
Z1-Z2: Variable left to right programmability of the backstops
X1-X2: Variable In and Out programmability of backstops
R1-R2: Variable Up and Down/Height programmability of backstops

2D Graphical programming via 10" display Up to 7,000+ job storage Infinite off-line job storage via USB port Fully supported by Standard Industrial Available with X, R, Z1-Z2, X1-X2, R1-R2 axis Operator prompts and on-line help messages USB Flash Drive Provides step by step instructions for part forming
Walks operator through part construction 2D Graphical Off-line Software (optional) Bend simulation checks for interference & overload

Optional Off-line 2D graphical software: Allows operator to fully build and program parts/jobs from PC, save onto memory stick and then download directly into 2D control via USB port ($500.00).

EVC Accessories

This control will also allow the operator to program an optionally supplied CNC controlled crowning unit (example: Wila E4, E-Wide, etc). It will also control optional following/support arms, thickness detectors (calipers) and robotics.

CNC Sheet Assists/Followers are controlled by the EVC 7 and the EVC Infinite controls

CNC crowning units are controlled by the EVC 5, EVC 7 and EVC Infinite

Series II Gauging System

--X axis travel speed is 1,100 inches per minute
--Available with: X/Y X/Y/R X/Y/R/Z1-Z2 X1-X2 R1-R2
--Standard with 20" of gauge travel with 24" of gauging (39" available optionally)
--R axis travel speed is 330 inches per minute
--Gauge axis repeatability +,- .001"
--For 100 through 400 ton x 14' press brakes (larger gauges avail.)

Fully articulated, extremely heavy duty fingers come standard on the Series II gauge. Gauge up to 3 different points allowing for a very wide range of forming

All Series II gauges have up to 1,100 inch per minute X axis gauge travel.
SUPER heavy duty construction with up to 1,100 lbs. of holding force.

Series II Gauge Pictured with X, R and Z1-Z2 axis

X1-X2 tilting gauge bars are available with the EVC 7 and Infinite controls.

EVC Infinite Series

3D Graphical programming via 15" full color display

Touch-screen display

DXF File transfer capability

Windows XP Pro operating system

Ethernet networking capability

Up to 2,000,000 hard drive parts programs

Fully supported by Standard Industrial

Robotics interface

Onsite training for gauge is included

Thickness detection interface

Provides step by step instruction for forming

2D Graphical Off-line Software

Bend simulation for interference & overload

Programming of the axis in tabular mode with automatic syntactical checks, automatic calculation of the R & Z positions and of the bending and crowning

CNC Crowning Control

The articulated robotic Cartesian Series gauging system comes standard the with EVC Infinite control with fully articulated X1-X2, Z1-Z2 and R1-R2 axis.